Carbon-encapsulated Fe nanoparticles from detonation-induced pyrolysis of ferrocene

Carbon-encapsulated Fe nanoparticles with size between 5 and 20 nm were synthesized via a picric acid-detonation-induced pyrolysis of ferrocene, which is characterized by a self-heating and extremely fast process. The nanoparticles exhibit well-constructed core-shell structures, with bcc-Fe cores and graphitic shells. The graphitic shells can protect effectively the cores against the attack of HNO₃ solution. The formation of the core-shell nanoparticles can be selectively controlled by adjusting the composition of the picric acid-ferrocene mixture, which determines C/Fe atomic ratio of the reaction system. The core-shell nanoparticles are preferably formed at low C/Fe atomic ratios, while tubular structures are formed at high C/Fe ratio. The possible pathway for the carbon-encapsulated Fe nanoparticles formation is discussed briefly.     

Effect of carbon fiber surface functional groups on the mechanical properties of carbon-carbon composites with HTT

The present investigation describes the quantitative measurement of surface functional groups present on commercially available different PAN based carbon fibers, their effect on the development of interface with resol-type phenol formaldehyde resin matrix and its effect on the physico-mechanical properties of carbon-carbon composites at various stages of heat treatment. An ESCA study of the carbon fibers has revealed that high strength (ST-3) carbon fibers possess almost 10% reactive functional groups as compared to 5.5 and 4.5% in case of intermediate modulus (IM-500) and high modulus (HM-45) carbon fibers, respectively. As a result, ST-3 carbon fibers are in a position to make strong interactions with phenolic resin matrix and HM-45 carbon fibers make weak interactions, while IM-500 carbon fibers make intermediate interactions. This observation is also confirmed from the pyrolysis data (volume shrinkage) of the composites. Bulk density and kerosene density more or less increase in all the composites with heat treatment up to 2600 °C. It is further observed that bulk density is minimum and kerosene density is maximum upon heat treatment at 2600 °C in case of ST-3 based composites compared to HM-45 and IM-500 composites. It has been found for the first time that the deflection temperature (temperature at which the properties of the material start to decrease or increase) of flexural strength as well as interlaminar shear strength is different for the three composites (A, B and C) and is determined by the severity of interactions established at the polymer stage. Above this temperature, flexural strength and interlaminar shear strength increase in all the composites up to 2600 °C. The maximum value of flexural strength at 2600 °C is obtained for HM-45 composites and that of ILSS for ST-3 composites.     

The crystallization characterization of bulk syndiotactic polystyrene sample: immediate evidence from IR spectroscopy

The crystallization characterization of bulk syndiothactic polystyrene (s-PS) sample is thoroughly studied using the Fourier transform infrared spectroscopy (FTIR). The WAXD is further used to identify the s-PS crystal formation to confirm the specific absorbance in FTIR spectra. Both melt and cold-crystallization behavior are quantitatively determined using FTIR spectra ranging from 870 to 820 cm⁻¹ at 264 °C. Fitting curves to IR spectra provides direct evidence of bulk s-PS crystallization behavior in quantification. The melt-crystallization process yields the β-form only; while the cold-crystallization process yields both the α and the β-form crystal in bulk s-PS sample. The β-form crystal is generated from the phase-transformation of the α-form crystal by cold-crystallization process, the α-form crystal is the initial phase. The activity energy of the α-form formation is lower that that of the β-form, suggesting that the α-form crystal is kinetically favorable while the β-form crystal is thermodynamically favorable.     

几种光谱方法(FTIR、FT-Raman,NMR)在橡胶分析中的应用

综述了傅里叶变换红外光谱 ,傅里叶变换拉曼光谱以及核磁共振波谱在橡胶结构的定性、定量分析中的应用     

Synthesis and characterization of a new water-soluble endohedral metallofullerene for MRI contrast agents

Water-soluble amino acid derivatives of gadolinium (Gd) endohedral metallofullerenes (AAD-EMFs), Gd@C₈₂O_m(OH)_n(NHCH₂CH₂COOH)_l (m ≈ 6, n ≈ 16 and l ≈ 8) are synthesized by a direct reaction of the pure endohedral metallofullerene Gd@C₈₂ with an excess of alkaline solution of β-alanine. The structure of the AAD-EMFs is characterized by FTIR, XPS and laser-desorption time-of-flight (LD-TOF) mass spectrometries. Water proton relaxivity analysis indicates that the longitudinal relaxivity R₁ (the effect on 1/T₁, 9.1 mM⁻¹ s⁻¹) of AAD-EMFs is higher than that of the commercial MRI contrast agent, Magnevist (gadolinium-diethylenetriaminepentaacetic acid, Gd-DTPA, 5.6 mM⁻¹ s⁻¹). The MRI phantom studies are performed to confirm the high efficiency of this sample as MRI contrast agents.     

交替惩罚三线性分解二阶校正荧光分析法快速测定牛奶中洛美沙星含量

笔者利用化学计量学交替惩罚三线性分解二阶校正算法结合荧光分析,在有干扰药物及牛奶中干扰组分共存下,对牛奶中的洛美沙星进行快速分析测定。当三维荧光数据的预估组分数取4时,所得平均回收率达到99.4%±1.3%,预测方差均方根(RMSP)为2.97nmol/L,预测结果良好。实验结果表明,此法可用于干扰组分共存下牛奶中洛美沙星的快速定量测定。     

Effect of calcination temperature on the low-temperature oxidation of CO over CoOx/TiO2 catalysts

A 5 wt% CoO_x/TiO₂ catalyst has been used to study the effect of calcination temperature on the activity of this catalyst for CO oxidation at 100 °C under a net oxidizing condition in a continuous flow type fixed-bed reactor system, and the catalyst samples have been characterized using TPD, XPS and XRD measurements. The catalyst after calcination at 450 °C gave highest activity for this low-temperature CO oxidation, and XPS measurements yielded that a 780.2-eV Co 2p_3/2 main peak appeared with this catalyst sample and this binding energy was similar to that measured with pure Co₃O₄. After calcination at 570 °C, the catalyst, which had possessed practically no activity in the oxidation reaction, gave a Co 2p_3/2 main structure peak at 781.3 eV which was very similar to those obtained for synthesized Co_nTiO_n+2 compounds (CoTiO₃ and Co₂TiO₄), and this catalyst sample had relatively negligible CO chemisorption as observed by TPD spectra. XRD peaks indicating only the formation of Co₃O₄ particles on titania surface were developed in the catalyst samples after calcination at temperatures ≥350 °C. Based on these characterization results, five types of Co species could be modeled to exist with the catalyst calcined at different temperatures. Among these surface Co species, the Type A clean Co₃O₄ particles were predominant on a sample of the catalyst after calcination at 450 °C and highly active for CO oxidation at 100 °C, and the calcination at 570 °C gave the Type B Co₃O₄ particles with complete Co_nTiO_n+2 overlayers inactive for this oxidation reaction.     

Polymeric sol–gel coatings as protective layers of aluminium alloys

Sol–gel route is an emerging technology to synthesize coatings of a wide variety of properties taylored. In this work three low temperature cured coatings has been studied to evaluate their protective properties in order to be used as protective barrier coatings for aluminium alloys with potential architectural and automotive applications. These three coatings are novel modified silane nanocomposites coatings obtained mixing two sols separately prepared: a pre-hydrolysed 3-glycidyloxypropyl trimethoxysilane (GPTS) with acidic catalyst and another obtained from tetraethylorthosilicate/methyltriethoxysilane (TEOS/MTES). Particulated coatings were obtained by addition of 25 wt.% particles of Aerosil 300 and Aerosil R972, respectively. The protective properties of the coatings were evaluated by electrochemical impedance spectroscopy (EIS) which showed notably differences among them not only from the protective viewpoint but the hydrophobic nature of the coatings and the controlling corrosion mechanism in each case.     

Frictional wear in high temperature thermotropic liquid crystalline polymers: correlation with glass transitions

Wholly aromatic thermotropic main chain liquid crystalline copolymers (LCPs) with varying glass transitions (T_g) were tested for wear resistance, particularly under high friction conditions, where surface temperatures can rise. Dynamic mechanical spectroscopy and DSC were used to characterize molecular relaxations. Three copolyester LCPs which all contain a substantial fraction of main chain 1,4-phenyl groups were chosen for this study. These included semi-crystalline Vectra^® A900, a semi-crystalline LCP containing phenyl hydroquinone (phHQ-LCP), and a low crystallinity LCP containing t-butyl substituted hydroquinone (t-butylLCP). These have glass transitions of 100, 160 and 175 °C, respectively, and heat deflection temperatures (HDTs) of 170, 260 and 174 °C, respectively. HDT is dependent in part on crystallinity. The wear performance was found to depend mainly on T_g and not HDT, suggesting a microscopic failure mechanism related to the amorphous phase. This is supported by the relatively poor elevated temperature wear performance of Vectra^® compared to the higher T_g LCPs. Shear strength measurements on the neat LCP resins did not correlate with wear properties of the blends, most likely because the measurements were made at room temperature and not elevated temperatures.